• First the dual frequency bands offer a high speed of 150Mbps on the 2.4Ghz band and 433Mbps on the 5Ghz band. 

• Moving further, with support for passive POE (power over ethernet) the deployment becomes extremely flexible. 

• It comes with a waterproof weathercase so it can easily withstand any weather condition be it rainfall, extreme cold or hot.

• The powerful external antennas provide better signal transmission as well as wider coverage.

• The Wavlink ac600 setup supports multiple modes. You can use it in an AP mode, range extender mode as well as you can use it as a router. 

• Further the range extender offers high security encryptions with WPA and WPA2. 

• Additionally, the smart LED light indicators allow the user to understand the exact working status of the device. 

Quick Installation Using WPS

For the Wavlink ac600 setup you do not need any expert assistance. As the setup takes less than five minutes. For the setup using WPS, the requirements are a vacant power outlet and a router with active internet plan. Here's how you can initiate the setup:

First with the help of the power adapter that came in the package contents activate the device. Initially the light will blink green, it means the outdoor extender is booting up. Let the power LED stabilize properly. Be mindful that during the initial setup there should be close proximity between the host router and the ac600 outdoor extender. 

Moving further search for the WPS key on the extender's panel. As you find it, push it. Thereafter within the time span of two minutes, push the WPS key of the host router also. The WPS light will activate, so you need to wait till the synchronisation completes. As the Wavlink ac600 setup using WPS completes the LED light will stop flickering and it will stabilize. 

Lastly, relocate the extender to your outdoor area where you need extended wireless signals. 

Alternate Setup Method Via Web Browser 

In case your router doesn't support the Wavlink ac600 setup via WPS or you want to customize network settings then the web browser setup method will be more convenient for you. The steps for it are also very simple, here's the guidance:

✓ First activate the range extender with the help of the supplied power adapter.

✓ Let the outdoor extender boot up properly. As it is ready for the setup, take your wifi enabled smart device. 

✓ Connect this device to the ac600’s wifi network. The details are scribed on the back panel of the extender so you can grab it from there. 

✓ After a successful connection, open an internet browser which is updated. You can choose Google chrome, internet explorer, firefox, edge, safari as well. 

✓ From hereon, move to the address field. In it enter 192.168.10.1. Push enter key. This web address will provide you entry to the Wavlink ac600 setup page. 

✓ Now you have to enter the username as well as the security key. The default details are given in the user manual. 

✓ As you get access to the admin panel, you just need to follow the directions that appear on your screen. Eventually the setup completes and all the front panel LED will turn solid green thus indicating a successful setup. 

Note: It's an expert recommendation to look for the pending firmware updates. As pending updates not only improve security of your Wavlink network, but also amp up the entire performance. So before finalizing the setup, head towards the firmware update section. Follow the instructions as they appear on your device screen to update the firmware. 

Factory Resetting Wavlink ac600 Extender 

There are many users who try the Wavlink ac600 setup process, but either leave it midway or the outcome is not in their favor. So to re perform the setup, factory resetting becomes crucial. Otherwise the setup will fail. Therefore here’s how you can do the same:

First make sure the ac600 outdoor range extender is active. Now look for the reset hole on the extender’s panel. You'll easily find it either at the bottom or at the back panel. As you find it, take any sharp object like a paper clip, sim ejector pin or a toothpick. Insert it in the hole, push and hold till the power LED starts to blink. Now release the key and let the extender reboot. Once done, you can follow the above-mentioned setup steps to gain access to the seamless wifi coverage in your outdoor areas.